1/2″ x 5 3/4″ Latigo Bit Hobble #BH41
$40.00
Available on backorder
Description: For use on any shank bit, this bit hobble has a beautiful hand braided rawhide ball and hand braided rawhide loop keepers. It is made of 1/2 inch latigo leather and is 5 1/8th inches wide. The latigo leather is edged hand-rubbed and waxed.
Shown on the horse is also the #DMR3 Round 3/8″ Nylon Mecate.
Related products
-
Single Buckle Leather Curb Strap #CU31
$30.00Description: The Single Buckle Leather Curb Strap #CU31 is made of 5/8 inch hand-edged harness leather that has been hand-rubbed, treated with Neatsfoot Oil and hand-rubbed again. The buckle is stainless steel and the leather under the buckle is hand stitched together to prevent the buckle from slipping out of position.
How it works: This is designed for use on a Ring, Offset D or Eggbutt Snaffle Bit. This nice functional curb is built of high quality materials that will hold up through years of hard use. It will not stretch or get limber with use and is easy to adjust.
Visit my Tack Talk article “Curb Your Enthusiasm” to learn more about curbs.
-
Curb Strap with Flat Chain #CU10
$33.00Description: This Curb Strap with Flat Chain #CU10 is made of an 1/2 inch wide chain attached between two 1/2 inch burgundy latigo leather straps that are hand-edged, hand-rubbed and waxed. The curb can be attached to the bit with the chain flat or with the chain in a twisted position. The beveled buckles, chain and wire loops are all made of stainless steel. This curb is AQHA legal when attached with the chain in the flat position.
How it works: The flat chain gives a stronger signal on the chin when the reins are tightened than any of the leather curbs. If the chain is attached in the twisted position the signal becomes even stronger (but is then not legal in AQHA shows).
See my Tack Talk article “Curb Your Enthusiasm” to learn more about curb straps.
-
Steel C Shank Bit with Silver #A4
Price range: $451.00 through $480.00Description: The bit has “Buster Welch” style 6 1/2 inch shanks made of high quality 4130 grade steel and overlaid with beautiful hand engraved nickel silver. Four mouthpieces are available (see pictures). All mouthpieces are 5 1/8 inch wide, are made of steel or steel and copper, have inlaid copper strips to promote salivation, and are made in the diameters listed in pictures and dropdown. The bit comes with the #BH51 3/8 inch Latigo Leather Bit Hobble as shown.
How it works: The angle of this shank allows time for the horse to respond to the reins being adjusted (pulled) before the mouthpiece contacts the sides of the mouth, tongue and roof of the mouth and the curb strap makes contact with the chin or vice-versa when the reins are released. This truly is a great little shank! Almost all horses respond to this shank with confidence and contentment. This is a favorite with professional horsemen.
Shown on sorrel horse in addition to the #A4 Steel C Shank Bit is the #HU1 Bosalita 1/2 Inch, the #DMR3 Round 3/8 inch Nylon Mecate, and the #BC2 Shaped Breast Collar, custom stamped.
-
Eggbutt Snaffle Bit #18
$150.00Description: The Eggbutt Snaffle Bit #18 is made of Stainless Steel. The mouthpiece is 5 1/8 inches wide, slightly bowed and has inlaid copper strips to increase salivation. It is 3/8th inch in diameter at the corners of the mouth and gradually tapers to 1/4 inch in the center.
How it works: When each rein is pulled the eggbutt snaffle bit will give a clearer signal than a ring snaffle because there is a larger area of contact on the corner of the mouth and contact on the opposite side of the face. This helps the colt to bring his whole face through the turn rather than just his nose. This bit is NRCHA & AQHA legal.
This is my favorite snaffle and I use it on almost all my young horses. Dennis
Shown on the horse in addition to the Eggbutt Snaffle is the #HS34 Doubled and Stitched Browband Headstall, the #CU31 Single Buckle Leather Curb and the #BLL2 Latigo on Latigo 5/8″ Heavy Reins.
-
Ring Snaffle Bit #17
Price range: $50.00 through $150.00Description: The Ring Snaffle Bit #17 is made of 5/16th inch steel. The rings are 2 3/4 inches in diameter. This snaffle is available with 4 mouthpieces (see picture). All mouthpieces are 5 1/8th inches wide. Mouthpiece #9 has inlaid copper bars to promote salivation.
Snaffle Bit Mouthpiece choices:
#0: This soft rubber mouthpiece is 11/16″ in diameter. This mouthpiece is designed for very sensitive horses. It is soft on the tongue and bars and can be an excellent first mouthpiece for colts.
#9: This steel 2 piece snaffle mouthpiece is 3/8” in diameter. This is a great tool for anyone who wants a quicker and more consistent response when a horse is asked to give his head. Champion trainers including Tarin Rice, Boyd Rice, Gerald Alexander, Robbie Boyce, Matt Koch, Brad Lund, & Bozo Rogers all use and really like the results they get with this snaffle. Some of their comments are: “more feel than any snaffle I’ve ever put in a horse’s mouth”, “best snaffle I’ve ever ridden”, “this snaffle works so well!”, “my colts are going to the futurity in this snaffle”.
#42: The 3/16th inch steel twisted wire is designed for the horse that has become resistant to the plain snaffle and needs a bit of extra signal on the corners of the mouth to respond correctly. This steel bit is especially built at this diameter to prevent it from pinching or grabbing the skin at the sides of the mouth.
#48: The 1/8 inch stainless twisted wire mouthpiece is specifically designed so it will not pull or pinch the corners of the horses mouth like a steel mouthpiece of the same size will. This small diameter combined with the twisted wire will help a horse that is resistant to a pull to respond quickly and correctly.
Although you should always check with show management, this snaffle with mouthpiece #9 is legal in AQHA & NRCHA snaffle bit classes. Shown is mouthpiece #9.
